EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 217 / 803

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

205

MAC/IP/UDP

Modify Frame Structure

Allows modifying the structure of the frame.



Global Option



S-OAM

check box when selected enables EtherSAM over service

OAM at Layer 2 on all services. The EtherSAM uses LBM and LBR
messages of the S-OAM protocol to perform the test. A device
having the capability to loopback LBM messages (via LBR) is
required at the remote. Only available with EtherSAM for rates up
to 10G WAN. Not available in Dual Test Set and Dual Port topology.



Provider Encapsulation

is available with single port EtherBERT

Framed Layer 2 and Traffic Gen & Mon test applications at rates of
10GE, 40GE, and 100GE. Choices are:

None

: No encapsulation.

EoE

: Ethernet over Ethernet encapsulation.

PBB-TE

: Provider Backbone Bridges with Traffic Engineering

encapsulation.



IP Version

allows selecting

IPv4

(default) or

IPv6

that will be used

for both the interface and all streams/services.

«
...
215
216
217
218
219
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Falcon Страницы: 3

Бренд: ZETRON Страницы: 3

Бренд: Kathrein Страницы: 16

Бренд: Kärcher Страницы: 4

Бренд: Lawler Страницы: 5

Бренд: Rain Bird Страницы: 138

Бренд: Rane Страницы: 2

Бренд: T&S Страницы: 5

Бренд: TCS Страницы: 16

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

Бренд: Tech 21 Страницы: 2

Бренд: Yolink Страницы: 23

Бренд: AirCycler Страницы: 2

Torque Converter Lock-Up

Бренд: TS Performance Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Waterbird Страницы: 19

MOBA-Matic MMC-1000

Бренд: MOBA Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды