EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 212 / 803

Test Setup - Test Configurator, Timer, and System

200

88000 Series

Local Details (iSAM)

Local Details (iSAM)

From the

Test

menu, tap

Setup

Test Configurator

, and the

More

button

from the

Local

block.

LINK



An arrow is used to indicate the status of the test link (at the PCS level
for parallel interfaces).



A green arrow indicates that the link is up.



A red arrow indicates that the link is down.



A gray arrow indicates awaiting incoming data to provide a status.



Interface/Rate

Port

choices depend on the rates available on the

module.

For 10GE WAN, the test uses the WIS default values for J0, J1, and C2 as
defined in

WIS Button

on page 191.



PHY Type

allows selecting the 100GE (4 Lanes) CFP4/QSFP transceiver

PHY type:

LR4/ER4

(default),

SR4

CWDM4

CLR4

, or

Other

. The PHY

type when set to any except

LR4/ER4

, allows enabling RS-FEC (see

page 182); ensure both ends of the circuit have the FEC enabled. Only
available with 100GE (4 Lanes) framed Ethernet interface.

100GE (4 Lanes) [103.125 Gbit/s]
40GE (4 Lanes) [41.25 Gbit/s]
10GE WAN
10GE LAN
1GE Optical
100M Optical
10/100/1000M Electrical

For 88200NGE, only possible when using an active copper SFP.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды