EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 183 / 803

Test Setup - Test Configurator, Timer, and System

Power Blazer

171

External Reference

External Reference

Allows the configuration of the external reference signal. Available with
Wander test application.

From the

Test

menu, tap

Setup

Test Configurator

, and tap on the

External Reference

block.

Reference

Mode

is set to

External Reference

Ext Reference In

Allow the selection of the reference signal for TE/TIE measurements.



Signal

allows the selection of the reference interface:

2 MHz

10 MHz

and

1PPS

. Only

1PPS

reference is available for 1PPS interface/rate test.

Ext Ref In

on a green background indicates that a valid reference is

received.

LOS

on a red background indicates that the received signal is not valid.



Connector

indicates the connector used for the external reference

signal:

RJ48C

BNC.



Frequency (MHz)

displays the frequency of the received reference

signal.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды