EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 411 / 803

Test Results

Power Blazer

399

Alarms/Errors Overview

STS-x/AU-x

Alarms



AIS-P

(Alarm Indication Signal - Path) - SONET

AU-AIS

(Administrative Unit - Alarm Indication Signal) - SDH

: The H1 and H2 bytes contain an all-ones pattern in three

consecutive frames or more.

: Generates an all-ones pattern over H1, H2, H3, and SPE.



LOP-P

(Loss Of Pointer - Path) - SONET

AU-LOP

(Administrative Unit - Loss Of Pointer) - SDH

: A valid pointer is not found in N consecutive frames (where



10), or that N consecutive NDFs (“1001” pattern) are detected

(non-concatenated payloads).

: Generates a non-valid pointer.



UNEQ-P

(Unequipped - Path) - SONET

HP-UNEQ

(HP - Unequipped) - SDH

: The C2 byte contains “00 H” in five consecutive frames. Only

available when PLM-P/UNEQ-P / HP-PLM/HP-UNEQ is enabled (refer to

Labels

on page 196).

: Generates an all-zeros pattern over POH and SPE.



H4-LOM

(H4 - Loss Of Multiframe)

: For VT/TU structured optical frames, the system loss track of the H4

byte multiframe indicator sequence.

: Generates a wrong H4 byte multiframe indicator sequence.



TIM-P

(Trace Identifier Mismatch - Path) - SONET

HP-TIM

(HP - Trace Identifier Mismatch) - SDH

: J1 Trace doesn’t match the expected message value. Only

available when TIM-P/HP-TIM is enabled (refer to

Traces (SONET/SDH)

on page 336).

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды