EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 377 / 803

Test Results

Power Blazer

365

Alarms/Errors Overview



Exc. Skew

(Excessive Skew)

: The skew exceeds the defined threshold (see

Skew Alarm

Threshold (bits)

on page 145).

Errors



Block

is available with Ethernet test applications and 100 GbE over

OTU4. Injection is not available when RS-FEC is enabled.

: Invalid 64b/66b block code are received. An invalid 64b/66b block

is declared when the synchronization field has a value of 00 or 11.



Inv. Marker

(Invalid Marker): Injection is not available when RS-FEC is

enabled.

: There are errors in the 66-bit block alignment marker.



PCS BIP-8

: There are PCS lane bit-interleave parity error. A routine even-parity

check is performed over all bits of a PCS lane, from and including the
previous alignment marker, but not including the current alignment
marker.



PCS BIP-8 Mask

is available with 40GbE over OTU3 test.

: At the OTN ingress, the calculated 8-bit error mask contains at least

one bit set to “1”.



OTN BIP-8

is available with 40GbE over OTU3 test

: Indicates for each lane that at the OTN egress, the calculated 8-bit

error contains at least one bit set to “1”.



FEC-SYMB

(Available with 400G when

RS-FEC (RX Only)

is enabled)

: FEC symbol errors are detected. The

FEC-SYMB

does not raise an

error, only the count and rate values are reported.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды