EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 117 / 803

Test Setup - Test Configurator, Timer, and System

Power Blazer

105

Test Configurator Overview



TA Status for a transceiver adapter is only displayed when there is a
warning or a problem as described in the following table.



Physical Interface Port indicates the physical interface port. For

Dual Port

topology, there is a physical interface for each port.

The status icon for a physical CFP4/CFP8/QSFP interface is
displayed as described in Port Status above.

Icon

Displayed Message

Description

Port A/B - Insertion counter approaching the limit TA insertion counter exceeds the insertion

counter threshold (90%).

Port A/B - Insertion limit is reached

TA insertion counter exceeds the module insertion
limit.

A1/A2/B1/B2 - Insertion counter approaching the
limit

Optical transceiver module insertion counter
exceeds the insertion counter threshold (90%).

A1/A2/B1/B2 - Insertion limit is reached

Optical transceiver module insertion counter
exceeds the insertion limit.

Port A/B - The battery for the insertion counter is
low, please contact EXFO Support

The battery is low and must be replaced by an
EXFO authorized service center.

Port A/B - The battery for the insertion counter is
depleted, please contact EXFO Support

The battery is dead and must be replaced by an
EXFO authorized service center.

A1/A2/B1/B2 - Missing TA-... Adaptor

No TA detected

A1/A2/B1/B2 - Validating TA-...

Validation process is on-going

A1/A2/B1/B2 - Invalid TA-... Adaptor

Validating process completed and incompatibility
has been found

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды