EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 285 / 803

Test Setup - Test Configurator, Timer, and System

Power Blazer

273

S-OAM and MPLS-TP OAM

Test Function

Note:

Test Function

parameters are not configurable when the

TX Enable

check

box is selected.



Function

allows the selection of the test function to be performed.



Loopback

(default) function is used to verify the bidirectional

connectivity to a peer MEP (

Continuous

check box cleared) and to

verify its capability to sustain close to line rate traffic (diagnostic
test;

Continuous

check box selected).



Test

function is used to generate a test signal and/or verify the

integrity of received test signal from the peer MEP.



Frame Delay

function is used to measure the round trip delay with

the peer MEP.



Frame Loss

function is used to measure the frame loss with the

peer MEP in both directions from a single end point.



Synthetic Loss

function is used to measure the frame loss with the

peer MEP in both directions from a single end point using synthetic
frames.



TX Enable

check box when selected (cleared by default) allows

transmission of frames. However the transmission will only begin
when the test is started or if the test is already running. When the

Continuous

check box is cleared, the

TX Enable

check box is

automatically cleared once all frames have been transmitted.



Address Type

, available with S-OAM Mode, defines the destination

address type of the frame:

Unicast

(default) or

Multicast

. Availability of

address types depend on selected S

-OAM Mode

and

Test Function



Continuous

check box when selected (default) specifies that the

frame generation is continuous. The

Continuous

check box is cleared

for Multicast address type.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды