EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 149 / 803

Test Setup - Test Configurator, Timer, and System

Power Blazer

137

1588 PTP

Alarm Timeout/Threshold

Note:

The following parameters are also used to declare the Pass/Fail verdict.



Receipt Timeout

defines the threshold used to declare a

Loss

Announce

Loss Sync

message alarm:

255

messages (default is

messages). A message is considered lost if not received within its

expected arrival time and a loss alarm is declared when the number of
consecutive lost messages is greater than or equal to the defined

Receipt Timeout



IPDV Threshold

defines the inter packet delay variation threshold

used to raise the

Unusable

message alarm. The alarm is raised when

IPDV is not within the configured

IPDV Threshold

0.001

1000ms

(default is

2ms

). The minimum value of 0.001 is adjusted when the

Sync

Delay Req

is set to 4 messages/s or less.

Quality Level

The quality level characterizes the clock quality in terms of network
synchronization.



QL Mismatch Monitoring

when selected (default) enables the Quality

Level mismatch monitoring.



Expected QL

allows, when

QL Mismatch Monitoring

check box is

selected, the selection of the Expected Quality Level value: default
value is

QL-EEC2/ST3

for G.8265.1 and

QL-SSU-B/ST3E

for G.8275.1.

Refer to page 448 for more information.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды