EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 409 / 803

Test Results

Power Blazer

397

Alarms/Errors Overview

Section/Line / RS/MS

Alarms



LOF-S

(Loss Of Frame - Section) - SONET

RS-LOF

(Regeneration Section - Loss Of Frame) - SDH

A SEF (SONET)/RS-OOF (SDH) defect on the incoming optical

signal persists for at least 3 milliseconds.

: Generates non-valid framing bytes (A1 and A2).



SEF

(Severely Errored Framing) - SONET.

RS-OOF

(Regeneration Section - Out-Of-Frame) - SDH.

: A minimum of four consecutive errored framing patterns are

received.

: Generates four consecutive errored framing patterns.



TIM-S

(Trace Identifier Mismatch - Section) - SONET

RS-TIM

(Regeneration Section - Trace Identifier Mismatch) - SDH

: The received J0 Trace doesn’t match the expected message value.

Only available when Enable TIM-S/RS-TIM check box is selected (refer
to

Traces (SONET/SDH)

on page 336).



AIS-L

(Alarm Indication Signal - Line) - SONET

MS-AIS

(Multiplex Section - Alarm Indication Signal) - SDH

Bits 6, 7 and 8 of the K2 byte contain the “111” pattern in five

consecutive frames.

: Generates a SONET/SDH signal that contains a valid Section

Overhead (SOH) / Regenerator Section Overthead (RSOH) and an
all-ones pattern on the SPE.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды