EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 309 / 803

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

297

Signal - Signal Configuration (DSn/PDH)

Note:

Bit 8 is the Least-Significant Bit (LSB) and bit 1 is the Most-Significant Bit
(MSB).



Payload Content

and

Set All

Payload Content

allows the selection of the payload content that will

be applied to all TX timeslots when tapping the

Set All

button:

Pattern

,

Idle

, or

Tone

.



TX

Tap once or several times on each timeslot until the desired payload
content appears:

Pattern

(default),

Idle

, or

Tone

. For E0, timeslots 0

and 16 (PCM30 and PCM30 CRC4) are not configurable; timeslot 0
generates the FAS/NFAS framing; timeslot 16 generates a static MFAS
frame when TX Signaling is disabled and generates a frame with
Signaling capability when TX Signaling is enabled.

Note:

For Pattern, the pattern used is the one selected from

Tone (Hz)

allows the selection of a tone for digital milliwatt testing.

The signal output power, when converted to analog, is 0 dBm. Choices
are

1000 Hz

and

1004 Hz

(default). The selected Tone applies to all

timeslots set to Tone.

Idle

uses the Idle code byte from the Idle field. Choices are

00

to

FF

.

The selected Idle code applies to all timeslots set to Idle. The default
setting is

7F

.

Note:

The timeslots set to Idle or Tone can be changed from Idle to Tone and vice
versa even when the test is running; the Idle and Tone values can also be
changed.

Binary

allows either displaying the Idle code values in binary (when

selected) or in hexadecimal (default).

«
...
307
308
309
310
311
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: NEC Страницы: 149

Бренд: NEC Страницы: 13

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

TruPortal TP-ADD-1DIP

Бренд: Interlogix Страницы: 9

Бренд: M-system Страницы: 3

Бренд: DSE Страницы: 2

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: Parker Страницы: 8

Бренд: Global Fire Equipment Страницы: 23

Бренд: KSB Страницы: 16

Бренд: Objective Imaging Страницы: 11

Бренд: Bentel Страницы: 88

Бренд: Zenith Страницы: 20

Бренд: DAY Страницы: 23

Lift Inverter L1000V

Бренд: YASKAWA Страницы: 282

Бренд: Danfoss Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды