EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 398 / 803

Test Results

386

88000 Series

Alarms/Errors Overview

OTUx

Note:

Available for OTU4, OTU3, OTU3e1, OTU3e2, OTU2, OTU2f, OTU1f, OTU2e,
OTU1e, and OTU1.

Alarms



AIS

(Alarm Indication Signal) available with serial interfaces only.

: Polynomial number 11 (PN-11) is over all OTU frame bits including

FAS and MFAS for at least 3 consecutive 8192 bit-interval.

: Generates polynomial number 11 (PN-11) over all OTU frame bits

including FAS and MFAS continuously.



BDI

(Backward Defect Indication)

: The BDI bit in the SM overhead field (byte 3, bit 5) is “1” for at least

5 consecutive OTU frames.

: Generates “1” for the BDI bit in the SM overhead field (byte 3, bit 5)

continuously.



BIAE

(Backward Incoming Alignment Error)

: The BEI/BIAE bits in the SM overhead field (byte 3, bits 1 to 4) are

“1011” for at least 3 consecutive frames.

: Generates “1011” for the BEI/BIAE bits in the SM overhead field

(byte 3, bits 1 to 4) continuously.



IAE

(Incoming Alignment Error)

: The IAE bit in the SM overhead field (byte 3, bit 6) is “1” for at least

5 consecutive OTU frames.

: Generates “1” for the IAE bit in the SM overhead field (byte 3, bit 6)

continuously.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды