EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 299 / 803

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

287

Signal (Transport)

Signal (Transport)

From the

Test

menu, tap

Setup

,

Test Configurator

, the interface block,

and the

Signal

tab.

Physical Interface - Optical

Note:

For electrical interface, see

Physical Interface - Electrical



Optical Lane

indicates the optical lane number for parallel interfaces.



Laser

1

indicates the status of the laser:

ON

with the laser pictogram

(emitting an optical laser signal) or

OFF

.



TX Power (dBm)

indicates, when supported, the transmit power level

of the optical lane/laser in dBm.



Wavelength (nm)

indicates, when supported, the detected lane/laser

wavelength.



RX Power (dBm)

indicates, when supported, the current received

power level of the optical lane/laser in dBm.

Green: Power level in range.
Yellow: Power level out-of-range.
Red: Loss of signal or power level is close to damage.
Gray: Invalid operational range value or not available/supplied by the
transceiver.

Optical Interface

Optical Lane Number

OTU3 (4 Lanes) [43.018 Gbit/s]
OTU3e1 (4 Lanes) [44.571 Gbit/s]
OTU3e2 (4 Lanes) [44.583 Gbit/s]
OTU4 (4 Lanes) [111.81 Gbit/s]

0 through 3

1. Displayed for each optical lane for parallel interfaces.

«
...
297
298
299
300
301
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: UE Страницы: 4

Бренд: Panasonic Страницы: 45

Бренд: Banner Страницы: 15

Бренд: bar Страницы: 2

Бренд: Walimex Pro Страницы: 68

Бренд: VAT Страницы: 39

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренд: Ros Страницы: 10

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренд: Daikin Страницы: 19

Бренд: Carel Страницы: 48

Controller CR100

Бренд: Sonos Страницы: 12

Бренд: SAGEMCOM Страницы: 2

Бренд: Instant Care Страницы: 2

Soluna Remote Control

Бренд: Rollei Страницы: 8

Бренд: TSM Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды