EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 748 / 803

background image

Glossary

736

88000 Series

Generic Framing Procedure (GFP)



Type HEC (tHEC) Field

: A two-octet field that contains a CRC-16

sequence to protect the integrity of the type field. The tHEC
sequence is computed over the core header bytes using standard
CRC-16. As with the cHEC, CRC-16 enables both single-bit error
correction and multibit error detection.



Channel Identifier (CID)

: A one-byte field that is only available

when the EXI field is configured to Linear. The CID byte is used to
indicate one of 256 communication channels at a GFP termination
point.



Spare

: A one-byte field that is only available when the EXI field is

configured to Linear. This field is reserved for future use.



Extension HEC (eHEC)

: A two-byte field that contains a CRC-16

check sequence that protects the integrity of the contents of the
extension. CRC-16 enables both single-bit correction and multibit
error detection.

The figure below explains how (in GFP-F) the transmitter encapsulates
one entire frame of the client data.

GFP-F vs. GFP-T Frame Structure

«
...
746
747
748
749
750
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Zolix Instruments Страницы: 22

Бренд: ZEHUS Страницы: 28

Бренд: Valfonta Страницы: 12

Бренд: Barco Страницы: 6

SmartSwitch 6000

Бренд: Cabletron Systems Страницы: 76

Бренд: Fantech Страницы: 2

Бренд: Bartlett Страницы: 7

Бренд: Vacon Страницы: 132

Бренд: Zamel Страницы: 2

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

Бренд: Jäger Страницы: 18

Бренд: Quickie Страницы: 108

Бренд: GARDINER TECHNOLOGY Страницы: 28

RC Electronic DPSI LCD

Бренд: Emcotec Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды