manualshive.com logo in svg

EXFO Power Blazer 88000 Series, Руководство пользователя

Экспертный тестер сетей EXFO Power Blazer 88000 Series - надежное устройство для тестирования и мониторинга сетей. Для ознакомления с возможностями и настройками прибора скачайте бесплатное руководство пользователя на manualshive.com. Узнайте как максимально эффективно использовать этот инструмент для анализа сетевых проблем.

Поделиться
Скачать
background image

Test Setup - Test Configurator, Timer, and System

168

88000 Series

EtherSAM - Global

Global Options

Per Direction Configuration

 check box when selected (default) 

specifies that the values can be configured independently for each 
direction (local to remote and remote to local) for 

Dual Test Set

 or for 

each port (P1 to P2 and P2 to P1) for 

Dual Port

; for 

Dual Port

 using a 

different rate on each port, the check box is forced selected. When the 

Per Direction Configuration

 check box is cleared the configuration 

will be coupled and the values apply to both directions/ports. 

Note:

For 

Dual Test Set

 the 

Per Direction Configuration

 is only available when 

the communication with the remote module is established. 

Pass/Fail Verdict

 check box when selected (default) enables the 

pass/fail verdict. A global pass/fail verdict is given for the EtherSAM test, 

Service Configuration

, and 

Service performance

 (for each service). 

The pass/fail verdict is based on the following criteria: 

Frame Loss

, 

Max Jitter

, 

Round-Trip Latency

, and 

Average RX Rate

. 

Latency Measurement Mode

, available with 

Dual Test Set

 for rates 

from 10M to 10GE, allows the selection of the latency measurement 
mode: 

Round-Trip

 (default) or 

One-Way

.  

Synchronization with an external 1PPS clock is required to perform 
One-Way Latency measurement. One-Way Latency is only possible 
when both local and remote 1PPS signal clocks are valid. The 
following alarms are available with One-Way Latency measurement.

LOPPS-L

 and 

LOPPS-R

 (Loss Of Pulse Per Second - Local/Remote) are 

declared when either no pulse is received or when no pulse is 
received within 1 second ± 6.6 

μ

s after the previous pulse. LOPPS-R is 

only monitored once the DTS connection is established. 

Restore EtherSAM Defaults 

Reverts the current test application to its default factory settings. 

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Calpeda IDROMAT 5 Quick Start Manual preview
IDROMAT 5
Бренд: Calpeda Страницы: 4
dbx DriveRack PA User Manual preview
DriveRack PA
Бренд: dbx Страницы: 52
Hankscraft Runxin HS Series Service Manual preview
HS Series
Бренд: Hankscraft Runxin Страницы: 58
DayTronic 3700 Series Instruction Manual preview
3700 Series
Бренд: DayTronic Страницы: 22
DayTronic System 10 User Manual Book preview
System 10
Бренд: DayTronic Страницы: 414
GAI-Tronics Elemec3 013-02-0095-002 Manual preview
Elemec3 013-02-0095-002
Бренд: GAI-Tronics Страницы: 12
Radware Alteon Installation And Maintenance Manual preview
Alteon
Бренд: Radware Страницы: 98
RabbitCore RCM2200 Getting Started Manual preview
RCM2200
Бренд: RabbitCore Страницы: 34
Valcom V-2003A Technical Specifications preview
V-2003A
Бренд: Valcom Страницы: 3
Valcom V-1092 User Manual preview
V-1092
Бренд: Valcom Страницы: 3
Valcom V-1092 Technical Specifications preview
V-1092
Бренд: Valcom Страницы: 2
We Care Solar Suitcase Installation Manual preview
Suitcase
Бренд: We Care Solar Страницы: 46
Watts 757 Series Assembly Manual preview
757 Series
Бренд: Watts Страницы: 4
Watts OneFlow OFTWH-R Installation And Operation Manual preview
OneFlow OFTWH-R
Бренд: Watts Страницы: 8
YASKAWA U1000 iQpump Drive User Manual preview
U1000 iQpump Drive
Бренд: YASKAWA Страницы: 426
YASKAWA Motoman DX200 Safety Notes preview
Motoman DX200
Бренд: YASKAWA Страницы: 26
YASKAWA motoman NX100 Instructions Manual preview
motoman NX100
Бренд: YASKAWA Страницы: 210
YASKAWA Z1000 CIMR-ZU*A Series User Manual preview
Z1000 CIMR-ZU*A Series
Бренд: YASKAWA Страницы: 400

Бренды по названию

Популярные бренды

Загрузить еще бренды