CC-ISOBUS CCI 50 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 359

background image

Settings

44

CAN trace

In the event of a complicated error pattern, the manufacturer's ser-

vice department can help. Then a recording of data traffic on the

ISOBUS, the CAN trace, can often prove helpful. The CAN trace con-

tains important information about the system status.
Continue working as normal during recording of the CAN trace. The

terminal is fully functional during this time.
The CAN trace is saved to the terminal internal storage and can only

be read out via the service menu.



Press the button "CAN trace".



The following operating screen opens:

You have the following operating options:

Enter the CAN trace recording duration
1.  Press the button "Duration".
2.  Enter the duration of the recording in seconds.
3.  Confirm your entry with "OK".

Start recording



Press the "Start recording" button (F12)

Note
The recording duration range is between 60 and 6000 seconds.

5.4.5

Show error memory

1. Press the button "Error memory".



A chronologically ordered list of error messages opens.

«
...
49
50
51
52
53
...
»

Содержание CCI 50








































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CCI 50

Бренд: ZETRON Страницы: 84

Бренд: Vectron Страницы: 48

Бренд: Equinox Systems Страницы: 2

Бренд: NEC Страницы: 24

digital video system

Бренд: IRIS Страницы: 8

Бренд: Bell System Страницы: 21

Бренд: Tailwind Страницы: 2

Бренд: ParTech Страницы: 2

Бренд: Zoeller Страницы: 48

Бренд: Omnicomm Страницы: 39

NetVista Kiosk DBCS

Бренд: IBM Страницы: 38

Бренд: ZKTeco Страницы: 27

Бренд: CCV Страницы: 24

Бренд: PaceBlade Страницы: 33

Бренд: TCi Страницы: 24

Бренд: National Instruments Страницы: 15

Бренд: POSBank Страницы: 2

Бренд: LOVATO ELECTRIC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды