CC-ISOBUS CCI 50 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 359

background image

39

5.4.2

Network members

Each network member connected to the ISOBUS provides basic in-

formation. This can for example be displayed for diagnostic purposes:



Press the button "Network members".



The Network members are identified and displayed:

Note
The object pool of all implements that have been connected at
least once is displayed. ISOBUS implements that are not currently
connected are displayed greyed out.

You have the following operating options:

Show information
1. Select a network member from the selection list.



Manufacturer, device class, function, function instance and
source address are displayed.

2. End the query with "OK".

Filter list



Press the "Filter list" button (F10).



Only the connected and active network members are dis-
played.

Reset filter



Press the "Reset filter" button (F11).



All network members are displayed.

«
...
44
45
46
47
48
...
»

Содержание CCI 50








































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CCI 50

Бренд: TEC Страницы: 24

Бренд: POSIFLEX Страницы: 10

Бренд: Spire Страницы: 2

Winterm 3125SE WBT

Бренд: Wyse Страницы: 2

Бренд: Quest Engineering Страницы: 34

Бренд: NCR Страницы: 306

UTG Ingenico 3070

Бренд: SHIFT4 Страницы: 64

Бренд: ANUBIS Страницы: 20

Бренд: Heartland Страницы: 7

Бренд: Heartland Страницы: 13

Бренд: Invenco Страницы: 67

Бренд: First Data Страницы: 7

Бренд: Ziosk Страницы: 11

Бренд: feedback Страницы: 26

Бренд: Ingenico group Страницы: 16

Бренд: PairGain Страницы: 40

Бренд: National Instruments Страницы: 11

Бренд: Panasonic Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды