CC-ISOBUS CCI 50 Скачать руководство пользователя страница 260

Страница: 260 / 359

CCI.Command

– Operation

4.3.2.1

Select field

To re-work an already stored

Field

proceed as follows:

1. Press the "Field" button on the

touchscreen

. If the button with the field name is

highlighted in white you can either press on the scroll wheel or on "OK".
→ A list of the stored

Fields

opens.

2. Select a

Field

from the list. To do so, press the button with the field name on

the

touchscreen

or turn the scroll wheel until this button is highlighted in white

and then press the scroll wheel.

3. Confirm your selection by pressing "OK", pressing the scroll wheel or pressing

the button with the field name once more.

Note

After starting

CCI.Command

, you can immediately start work. The selection of a

saved

Field

is not necessary.

Содержание CCI 50






































































































































































































































































































































































Результаты поиска

Содержание CCI 50

Отзывы:

Похожие инструкции для CCI 50

Бренды по названию

Популярные бренды

CC-ISOBUS CCI 50, Руководство по эксплуатации

Результаты поиска

Содержание CCI 50

Отзывы:

Похожие инструкции для CCI 50

Бренды по названию

Популярные бренды