CC-ISOBUS CCI 50 Скачать руководство пользователя страница 319

Страница: 319 / 359

CCI.Command

– Operation

Section Control: manual mode and auto mode

In manual mode, the sections must be switched on or off in implement operation or
manually using the joystick.

The worked area is recorded.

After activation of auto mode,

CCI.Command

transfers commands for switching

sections on and off to the implement.

For some implements, the

Section Control

functionality must also first still be

started in implement operation. See the manufacturer's operating instructions for
the procedure.

4.4.10 Change Section Control mode

The change into manual mode and auto mode takes place via the same button
(F4). The system changes according to which mode is currently selected:

Switch Section Control into auto mode

Switch Section Control into manual mode

To change between manual mode and

Section Control

auto mode, proceed as

follows:

1. Press the "Auto mode" or "Manual mode" button (F6) on the

touchscreen

→ The mode changes and the symbol on the F6 button changes.

Note

This function is only available if implement data is transferred.

Содержание CCI 50






































































































































































































































































































































































Результаты поиска

Содержание CCI 50

Отзывы:

Похожие инструкции для CCI 50

Бренды по названию

Популярные бренды

CC-ISOBUS CCI 50, Руководство по эксплуатации

Результаты поиска

Содержание CCI 50

Отзывы:

Похожие инструкции для CCI 50

Бренды по названию

Популярные бренды