manualshive.com logo in svg

Bull ESCALA PL860T/R, Процедуры снятия и замены, Страница: 58 / 218

Поделиться
Скачать
Bull ESCALA PL860T/R Скачать руководство пользователя страница 58

12.

Disconnect the cables, if any, from the back of the disk drive backplane

1.

Media device cable connector

(A)

can

remain connected.

2.

Squeeze the media device cable connectors

(B)

and

(C)

as shown and disconnect them

from their connector sockets on the disk
unit backplane.

Note:

Some systems might have

additional cables attached to the disk unit
backplane; not all cabling options appear
in the illustration.

3.

If there are other cables connected to the
disk unit backplane, disconnect them from
their connector sockets on the disk unit
backplane, noting their attachment points.

13.

Remove the media device

1.

While pushing the media device release
latches

(A)

, grasp the device

(B)

and begin

to pull it out of the system unit.

2.

Disconnect the cable attached to the back
of the media device.

3.

Finish pulling the media device out of the
system unit.

50

Power Systems: IBM Power 550 Express (8204-E8A and 9409-M50) removal and replacement procedures

Содержание ESCALA PL860T/R



























































































































































































































Отзывы:

Нет отзывов