manualshive.com logo in svg

Bull ESCALA PL860T/R, Процедуры снятия и замены, Страница: 46 / 218

Поделиться
Скачать
Bull ESCALA PL860T/R Скачать руководство пользователя страница 46

5.

If you removed the power cords, reinstall the
power cords for all of the power supplies.

6.

Go to Verifying a repair.

This completes this procedure.

Rebuilding data on a replacement disk drive using Linux

Use this procedure to rebuild data on a replacement disk drive.

To rebuild data on the replacement disk drive, complete the steps listed here.

For an unprotected disk drive

If the disk drive you are replacing is in a RAID Level 0 disk array or in a failed RAID Level 5 or RAID
Level 10 disk array, perform these tasks:

1.

Re-create the disk array.

2.

Re-create the file systems on the disk array.

3.

Copy the data back to the restored disk array from your backup media.

For information on these tasks, see the

PCI-X SCSI RAID Controller Reference Guide for Linux

, SA23-1327.

Replacing the disk drive using IBM i

Use this procedure to remove and replace a disk drive concurrently with IBM i.

38

Power Systems: IBM Power 550 Express (8204-E8A and 9409-M50) removal and replacement procedures

Содержание ESCALA PL860T/R



























































































































































































































Отзывы:

Нет отзывов