manualshive.com logo in svg

Bull ESCALA PL860T/R, Процедуры снятия и замены, Страница: 40 / 218

Поделиться
Скачать
Bull ESCALA PL860T/R Скачать руководство пользователя страница 40

12.

Look for the disk drive at the PCI location you recorded. The disk drive might have a Failed status.

13.

If the disk drive you want to replace is unprotected or in use, move the data from the disk drive
before continuing with this procedure.
For information, see the

PCI-X SCSI RAID Controller Reference Guide for Linux

.

14.

Type option

1

(Display hardware resource information details) next to the disk drive you want to

replace. Press Enter.
A Disk Hardware Resource Information Details display similar to the following is shown.

15.

Record the physical location information.

16.

Return to the IBM Power RAID Configuration Utility display.

Display Hardware Status

Type option, press Enter.

1=Display hardware resource information details

OPT Name

PCI/SCSI Location

Description

Status

--- ------ -------------------------- ------------------------- ----------------

0000:01:01.0.0/

PCI-X SCSI Adapter

Operational

0000:41:01.0.1/

PCI-X SCSI Adapter

Operational

sda

0000:41:01.0.1/0:3:0

Physical Disk

Active

sdb

0000:41:01.0.1/0:4:0

Physical Disk

Active

sdc

0000:41:01.0.1/0:8:0

Physical Disk

Active

sdd

0000:41:01.0.1/1:3:0

Physical Disk

Active

sde

0000:41:01.0.1/1:4:0

Physical Disk

Active

sdf

0000:41:01.0.1/1:5:0

Physical Disk

Active

0001:61:01.0.2/

PCI-X SCSI RAID Adapter

Operational

sdg

0001:61:01.0.2/0:3:0

Physical Disk

Active

0001:61:01.0.2/0:6:0

Advanced Function Disk

Active

sdi

0001:61:01.0.2/0:9:0

Physical Disk

Active

sdh

0001:61:01.0.2/255:0:0

RAID 10 Disk Array

Failed

0001:61:01.0.2/0:4:0

RAID 10 Array Member

Failed

0001:61:01.0.2/0:5:0

RAID 10 Array Member

Failed

e=Exit

q=Cancel

r=Refresh

t=Toggle

Figure 2. Example Display Hardware Status

Disk Unit Hardware Resource Information Details

Manufacturer . . . . . . . . . . . . . . : IBM
Product ID . . . . . . . . . . . . . . . : ST336607LC
Firmware Version . . . . . . . . . . . . : 43353048 (C50H)
Serial Number. . . . . . . . . . . . . . : 00006719
Capacity . . . . . . . . . . . . . . . . : 36.40 GB
Resource Name. . . . . . . . . . . . . . : /dev/sdd

Physical location
PCI Address. . . . . . . . . . . . . . . : 0001:50:01.0
SCSI Host Number . . . . . . . . . . . . : 2
SCSI Channel . . . . . . . . . . . . . . : 0
SCSI Id. . . . . . . . . . . . . . . . . : 4
SCSI Lun . . . . . . . . . . . . . . . . : 0

Extended Details
FRU Number . . . . . . . . . . . . . . . : 00P2676

More...

Press Enter to Continue

e=Exit

q=Cancel

f=PageDn

b=PageUp

Figure 3. Example Disk Hardware Resource Information Details display

32

Power Systems: IBM Power 550 Express (8204-E8A and 9409-M50) removal and replacement procedures

Содержание ESCALA PL860T/R



























































































































































































































Отзывы:

Нет отзывов