manualshive.com logo in svg

Bull ESCALA PL860T/R, Процедуры снятия и замены, Страница: 134 / 218

Поделиться
Скачать
Bull ESCALA PL860T/R Скачать руководство пользователя страница 134

19.

Remove all PCI adapters

1.

Record the slot number and location of
each adapter being removed.

2.

Slide the adapter latch

(A)

in the direction

shown to release the adapter

(B)

.

3.

Carefully grasp the PCI adapter by its top
edge or upper corners, and pull the
adapter straight out of its connector on the
system backplane.

4.

Store the adapter in a safe place.

5.

Repeat these steps until ALL PCI Card
Adapters are removed.

20.

Remove the GX adapter card if present

1.

Slide the adapter latch

(A)

in the direction

shown to release the adapter card.

2.

Squeeze the latches

(B)

to release them

from the adapter card and rotate them in
the direction shown.

3.

Gently pull the adapter card straight out
of the system.

4.

Repeat these steps to remove a second GX
adapter card, if present.

126

Power Systems: IBM Power 550 Express (8204-E8A and 9409-M50) removal and replacement procedures

Содержание ESCALA PL860T/R



























































































































































































































Отзывы:

Нет отзывов