manualshive.com logo in svg

Bull ESCALA PL860T/R, Процедуры снятия и замены, Страница: 138 / 218

Поделиться
Скачать
Bull ESCALA PL860T/R Скачать руководство пользователя страница 138

27.

Remove the system backplane

1.

Label and disconnect all ethernet cables
that are present.

2.

Remove the 6 screws

(A)

as shown in the

illustration.

3.

Push the system backplane

(B)

towards

the front of the system.

4.

Lift the system backplane up and out of
the system chassis.

5.

Note:

Use care when removing the system

backplane. Do not lift the system
backplane by any of the attached modules.

28.

Install the system backplane

Note:

Use care when replacing the system

backplane.

1.

Carefully grasp the replacement system
backplane

(A)

along two edges.

2.

Note:

Ensure the pin holes on the system

backplane are lined up correctly with the
pins

(B)

on the system chassis.

3.

Lower the system backplane at an angle,
with the back of the backplane connecting
with the system chassis first.

4.

Slide the system backplane towards the
back of the system chassis.

5.

Tighten the 6 screws

(C)

securing the

system backplane to the system chassis.

6.

Reconnect all ethernet cables that were
previously removed.

130

Power Systems: IBM Power 550 Express (8204-E8A and 9409-M50) removal and replacement procedures

Содержание ESCALA PL860T/R



























































































































































































































Отзывы:

Нет отзывов