manualshive.com logo in svg

Bull ESCALA PL860T/R, Процедуры снятия и замены, Страница: 142 / 218

Поделиться
Скачать
Bull ESCALA PL860T/R Скачать руководство пользователя страница 142

35.

Install the GX adapter card if previously removed

1.

Align the adapter card with the expansion
slot and its connector on the system
backplane.

2.

With the latches

(A)

in the open position,

gently push the adapter card straight into
the system.

3.

Rotate the latches in the direction shown
until they latch.

4.

Slide the adapter latch

(B)

back into place

in the direction shown to secure the
adapter card.

5.

Repeat these steps to install a second GX
adapter card, if previously removed.

36.

Install all PCI adapters

1.

Carefully grasp the adapter

(A)

by its top

edge, and align the adapter with the
expansion slot and its connector on the
system backplane.

2.

Press the adapter firmly into its connector.

3.

Slide the adapter latch

(B)

in the direction

shown to secure the card.

4.

Repeat these steps until ALL PCI Card
Adapters are installed.

134

Power Systems: IBM Power 550 Express (8204-E8A and 9409-M50) removal and replacement procedures

Содержание ESCALA PL860T/R



























































































































































































































Отзывы:

Нет отзывов