manualshive.com logo in svg

Bull ESCALA PL860T/R, Процедуры снятия и замены, Страница: 48 / 218

Поделиться
Скачать
Bull ESCALA PL860T/R Скачать руководство пользователя страница 48

4.

Determine if the failing disk drive is parity protected:

Check the status of the failing disk drive for one of the
following:

DPY/Active

DPY/Failed

DPY/HDW Failure

DPY/Degraded

DPY/Power Loss

DPY/Not Ready

DPY/Unknown

If the status of the failing disk drive and all other disk
drives in the array have a status listed above, the failing
disk drive is parity protected.

Is the failing disk drive parity protected?

Yes:

Go to step 9 on page 41.

No:

Continue with the next step.

Note:

An ASP with a status of Unprotected might

contain disk drives that are device parity protected.

5.

Perform a backup of the data in the failing ASP.

Go to step 9 on page 41.

Note:

This is a customer task. Refer to the system’s

Operations Guide for instructions.

6.

Does the disk drive you are replacing have a status of
Suspended?

Yes:

Go to step 9 on page 41.

No:

Check the status of the disk drive that is

mirrored to the disk drive you are replacing. If it is
Suspended, go to step 8 on page 41. If it is Active,
continue with the next step.

7.

Suspend the disk drive that you are replacing by performing the following:

1.

Press F3 from the Display Disk Configuration display to return to the Work with Disk Units display.

2.

Select Work with Disk Unit Recovery from the Work with Disk Units display and press Enter.

3.

Select Suspend mirrored protection from the Work with Disk Unit Recovery display and press Enter.

4.

Select the option to suspend the disk drive that you are replacing from the Suspend Mirrored Protection display
and press Enter.

5.

Go to step 9 on page 41

40

Power Systems: IBM Power 550 Express (8204-E8A and 9409-M50) removal and replacement procedures

Содержание ESCALA PL860T/R



























































































































































































































Отзывы:

Нет отзывов