Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 4

Страница: 4 / 85

70410501

28. Igniter Does Not Glow – Johnson Controls

Glow-Bar System........................................................................42

29. Igniter Glows Constantly – Johnson Controls and

White Rodgers Glow-Bar System...............................................43

30. Igniter Glows, Cycles Off But Burner Does Not Ignite

– Johnson Controls Glow-Bar System ........................................44

31. Igniter Does Not Glow – White Rodgers Glow-Bar System ......45
32. Igniter Glows, Cycles Off But Burner Does Not Ignite

– White Rodgers Glow-Bar System............................................46

33. Igniter Sparks, No Main Burner Ignition

– Instant Electronic Ignition........................................................47

34. CSH OM Models: No Heat With Cycle Selected,

Unit Running and Calling For Heat ............................................48

35. OM Models: No Start With Cycle Selected, Start Button

Pressed and Door Closed ............................................................50

36. OM Models: No Display After Selecting One Of The

ON/SELECT Keys......................................................................52

37. CE OM Models: No Heat With Cycle Selected, Unit

Running and Calling For Heat ....................................................53

38. CG OM Models: No Heat With Cycle Selected, Unit

Running and Calling For Heat ....................................................55

39. OM Models: No Fan Motor Rotation With Cycle Selected

and Start Pressed .........................................................................57

40. MM Models: Fan Motor Does Not Run With Door Closed,

Cycle Selected and Start Button Pressed ....................................58

41. MM Models: Cylinder Motor Does Not Run or Reverse With

Door Closed, Cycle Selected and Start Button Pressed In
Reversing Mode or Nonreversing Mode.....................................59

42. MM Models: No Heat With Cycle Selected, Unit Running

and Calling For Heat ...................................................................61

43. MM Models: No Heat With Cycle Selected, Unit Running

and Calling For Heat ...................................................................63

44. OM Reversing Models: No Cylinder Rotation or Reversing

Capabilities..................................................................................65

45. MM Models: No Display After Pressing the ON/SELECT

Keys ............................................................................................67

46. MM Models: Motor Does Not Run With Door Closed, Cycle

Selected and Start Button Pressed...............................................68

47. MM Models: Cylinder Motor Does Not Run or Reverse With

Door Closed, Cycle Selected and Start Button Pressed In
Reversing Mode or Nonreversing Mode.....................................69

48. MM Nonreversing Models: Motor Does Not Run With Door

Closed, Cycle Selected and Start Button Pressed .......................71

49. CD Models: No Start With Vend Satisfied and Start Button

Pushed .........................................................................................73

50. CD Models: No Heat With Vend Satisfied and Unit Running ...75
51. CD Models: No Heat With Vend Satisfied and Unit Running ...77
52. CD Models: No Start With Vend Satisfied and Start Button

Pushed .........................................................................................79

53. CD Models: No Start With Vend Satisfied and Start Button

Pushed .........................................................................................81

Section 4 – Adjustments ........................................................................82

54. Cylinder Clearance......................................................................82

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды