Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 70

Страница: 70 / 85

70410501

Troubleshooting

46. MM Models: Motor Does Not Run With Door Closed, Cycle Selected and

Start Button Pressed

208-240 Volt/60 Hertz/3 Phase Gas and Steam Reversing and Nonreversing; 480 Volt/60 Hertz/
3 Phase Gas Nonreversing; 480 Volt/60 Hertz/3 Phase Steam Reversing

NOTE: Make sure fuse on x1 of transformer is operational (480 Volt/60 Hertz/3 Phase units).

MM Models: Motor does

not run with door closed,

cycle selected and start

button pressed

Is there voltage

to the COM of the

door switch?

TMB2173S

Correct wiring

between door
switch and L1

supply for 208-

240 Volt units.

Check between

door switch and

X1 of transformer

for 480 Volt/3

Phase units.

Replace

motor.

Is there 120 VAC

to the N.O. terminal of

the door switch?

Check for proper

operation of door

switch arm and/

or replace door

switch.

Is there 120 VAC

to terminal P2 of the

micro control?

Correct wiring

between door

switch and micro

control.

Is there 120 VAC

to terminal P1 of the

micro control?

Replace

micro control.

Is there 120 VAC

across the coil of

the motor

contactor?

Correct wiring

to the coil

of motor

contactor.

Is there voltage

to terminals L1, L2

and L3 of motor

contactor?

Correct wiring

between

motor

contactor and

terminals L1,

L2, L3 and

TB1.

Is there voltage

at terminals T1, T2

and T3 of the M

contactor?

Replace

motor

contactor.

Is there voltage

to L1, L2 and L3

at motor?

Correct wiring

between

motor and

motor

contactor.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды