Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 73

Страница: 73 / 85

70410501

Troubleshooting

48. MM Nonreversing Models: Motor Does Not Run With Door Closed, Cycle

Selected and Start Button Pressed

120 Volt/60 Hertz/1 Phase Gas and Steam; 208-240 Volt/60 Hertz/3 Phase Gas; 480 Volt/60
Hertz/3 Phase Steam

NOTE: Voltage checks referenced to are for neutral unless stated otherwise.

MM Nonreversing Models:

Motor does not run with

door closed, cycle selected

and start button pressed

Is there

120 VAC to the

COM of the door

switch?

TMB2175S-a

Correct wiring

between door
switch and L1
supply for low

voltage units.

Check between

door switch and x1

of transformer for

high voltage units.

Is there

120 VAC to the N.O.

terminal of the door

switch?

Check for proper

operation of door

switch arm and/

or replace door

switch.

Yes

Is there

120 VAC to

terminal P2 of the

micro control?

Correct wiring

between door

switch and

micro control.

Is there

120 VAC to terminal

P1 of the micro

control?

Replace micro

control.

Gas Models:

Is there 120 VAC

across the coils of

the CR1?

Correct wiring

to the coil of

CR1.

Gas Models:

Is there 120 VAC

to terminal 1

on CR1?

Correct wiring

between terminal

1 and door switch.

Gas Models:

Is there 120 VAC

to terminal 3

on CR1?

Replace

CR1.

Gas Models,

120 VAC units: Is there

120 VAC across the

terminals 1 and 4 of

the motor?

Correct wiring

to motor.

Yes

Continued on

Steam Models:

Is there 120 VAC

across M coil?

Correct the

wiring to M coil.

Replace

motor.

Yes

Yes - Steam Models

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды