Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 71

Страница: 71 / 85

70410501

Troubleshooting

47. MM Models: Cylinder Motor Does Not Run or Reverse With Door Closed,

Cycle Selected and Start Button Pressed In Reversing Mode or
Nonreversing Mode

208-240 Volt/60 Hertz/3 Phase Gas and Steam Reversing and 480 Volt/60 Hertz/3 Phase Steam
Reversing Models

NOTE: If unit will not reverse when reversing is selected, check for proper operation and wiring of reversing
switch. Replace if necessary.

MM Models: Cylinder motor

does not run or reverse with

door closed, cycle selected

and start button pressed in

reversing mode or

nonreversing mode

there120 VAC

to the COM terminal

of the door

switch?

TMB2174S-a

Correct wiring

between door
switch and L1

supply for

208-240 units.

Check

transformer on

480 Volt

machines.

there 120 VAC

to the N.O. terminal

of the door

switch?

Check for proper

operation of door

switch arm and/

or replace door

switch.

Yes

there 120 VAC

to terminal P2 of

the micro

control?

Correct wiring

between door

switch and

micro control.

there 120 VAC

to terminal P1 of

the micro

control?

Replace

micro control.

there 120 VAC

across the coils of

the motor

contactor?

Correct wiring

to the coil of

motor

contactor.

there voltage

to terminals L1, L2

and L3 of motor

contactor?

Correct wiring

between motor

contactor

terminals and L1,

L2, L3 of TB1.

there voltage

at terminals T1, T2

and T3 of the M

contactor?

Replace motor

contactor.

there voltage

to terminals T1,

T2, T3 on the forward
contactor and voltage
to terminals U, V and

W on the reversing

contactor?

Correct wiring

between forward

contactor and motor

contactor and/or

correct wiring

between reverse

contactor and motor

contactor.

Yes

Continued on

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды