Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 58

Страница: 58 / 85

70410501

Troubleshooting

38. CG OM Models: No Heat With Cycle Selected, Unit Running and Calling

For Heat (continued)

120 Volt/60 Hertz/1 Phase and 208-240 Volt/60 Hertz/1 Phase Nonreversing
208-240 Volt/60 Hertz/3 Phase and 460-480 Volt/60 Hertz/3 Phase Reversing and Nonreversing

TMB2165S-b

Is there

voltage to the

input of the

cabinet

limit?

Correct wiring

between cabinet

limit and CR1.

Unit

operational.

Continued from

Is there

voltage to the

output of the

cabinet

limit?

Replace

cabinet limit.

Is there

voltage to

COM terminal

of the airflow

switch?

Correct wiring

between airflow

switch and cabinet

limit.

Is there

voltage to the

N.O. terminal

of the airflow

switch?

Check for proper

operation and airflow.

Replace airflow

switch if necessary.

Yes

Is there

voltage to the

input of the

stove limit?

Correct wiring

between stove

limit and airflow

switch.

Check for proper

airflow. Replace

stove limit if

necessary.

Is there

voltage to the

output of the

stove limit?

Correct wiring

between ignition

control and

stove limit.

Is there

voltage to

terminal 2 of

the ignition

control?

Does the

igniter

spark?

Check for proper gap on

igniter and check for

proper resistance of

ignition cable. Replace

if necessary.

Is there

voltage at

terminal 1 of

the ignition

control?

Replace

ignition control.

Is there

voltage across

the gas

valve?

Correct wiring

to gas valve.

Is there

a flame?

Check for gas flow and proper

gas pressure. Replace gas

valve or coils of gas valve.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды