Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 78

Страница: 78 / 85

70410501

Troubleshooting

50. CD Models: No Heat With Vend Satisfied and Unit Running (continued)

208-240 Volt/60 Hertz/3 Phase Gas Nonreversing

NOTE: All voltage checks are referenced to neutral unless stated otherwise.

there voltage to

the input of the

adjustable bulb

thermostat?

TMB2177S-b

Does the

igniter spark?

Check for proper igniter
gaps and resistance for

high voltage lead. (Proper

gaps for igniter are 5/16

above burner and 5/32
between electrode and

grounding tab. The proper

resistance of the high

voltage lead is between

5,000 Ohms and 25,000

Ohms.)

Is there voltage

across V1 and V2 of

the IEI board?

Replace

IEI board.

Yes

Continued from

there voltage to
the output of the

adjustable bulb

thermostat?

Replace

adjustable bulb

thermostat.

Correct wiring

between

thermostat and

switch B.

Yes

Is there voltage

across the coils of the

gas valve?

there gas pressure

on the output side

of the gas

valve?

Replace

gas valve.

Check for proper gas

pressure. 3.5 water

column inches for Natural

Gas, 10.5 water column

inches for L.P. Gas.

Yes

Is there a

flame?

Unit is

operational.

Yes

Correct wiring

between gas

valve and IEI

board.

Is there voltage

to the ignition

control board?

Correct wiring

between IEI

board and

thermostat.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды