Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 62

Страница: 62 / 85

70410501

Troubleshooting

41. MM Models: Cylinder Motor Does Not Run or Reverse With Door Closed,

Cycle Selected and Start Button Pressed In Reversing Mode or
Nonreversing Mode (continued)

480 Volt/60 Hertz/3 Phase Steam Reversing and 208-240 Volt/60 Hertz/3 Phase Gas and Steam
Reversing Models

NOTE: If the unit will not reverse when reversing is selected, check for proper operation and wiring of
reversing switch. Replace if necessary.

Is there

voltage to L1, L2, L3 on

the forward contactor or

voltage to terminals X, Y

and Z on the reversing

contactor?

TMB2168S-b

there voltage

to L1, L2 and L3 at

the cylinder

motor?

Unit

operational.

Is there voltage

at the CW or CCW

terminal on the solid

state timer?

Correct wiring

between the

solid state timer

and either the

forward or

reversing coil.

Is there voltage

at L1 of the solid

state timer?

Replace solid

state timer.

Yes

Continued from

Is there

voltage across the

coils of either the

forward or

reversing

contactor?

Replace either

the forward or

reversing

contactor.

Correct wiring between

cylinder motor and

forward or reversing

contactor.

Yes

Is there voltage

to the output of the

auxiliary contacts on the

motor contactor?

Correct wiring

between motor

contactor and

solid state timer.

Yes

Is there voltage

to the input side of the

auxiliary contacts on the

motor contactor?

Replace motor

contactor.

Correct wiring

between motor

contactor and

TB1-L1 supply.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды