Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 50

Страница: 50 / 85

70410501

Troubleshooting

34. CSH OM Models: No Heat With Cycle Selected, Unit Running and Calling

For Heat

120 Volt/60 Hertz/1 Phase and 208-240 Volt/60 Hertz/1 Phase Nonreversing
208-240 Volt/60 Hertz/3 Phase and 460-480 Volt/60 Hertz/3 Phase Reversing and Nonreversing

CSH OM Models:

No heat with cycle selected,

unit running and calling for heat

Is there

voltage

at H2-13?

Is there

voltage

at H2-6?

Correct wiring

between H2-6

and H2-13.

TMB2161S-a

Replace

micro control.

Is there

voltage

at H2-5?

Check for proper thermistor

operation. Replace

micro control if necessary.

Is there

voltage to the

input of the motor

relay?

Correct wiring between

motor relay and

micro control.

Is there

voltage to the

output of the
motor relay?

Replace

motor relay.

1 Phase

Only: Is

there voltage

to terminal 3

of CR1?

Correct wiring between

CR1 and motor relay.

3 Phase

Only: Is

there voltage

to the input of

the motor

switch?

Is there

voltage

to terminal 5

of CR1?

Correct wiring to

motor switch.

Is there

voltage to the

output of the

motor switch?

Replace

motor.

Is there

voltage to

terminal 3 of

the motor?

Replace

motor.

Is there

voltage across

the coil

of CR1?

Correct wiring

to CR1.

Does CR1

operate?

Replace

CR1.

Yes

Continued on

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды