Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 59

Страница: 59 / 85

70410501

Troubleshooting

39. OM Models: No Fan Motor Rotation With Cycle Selected and Start

Pressed

208-240 Volt/60 Hertz/3 Phase and 480 Volt/60 Hertz/3 Phase CE Reversing Models; 208-240
Volt/60 Hertz/3 Phase and 460-480 Volt/60 Hertz/3 Phase CG Reversing and CSH Models

OM Models: No fan motor

rotation with cycle selected

and start pressed

Is there

voltage across the

primary of the

transformer?

TMB2166S

Correct wiring to

transformer.

Check fuses.

Is there

24 VAC across

terminals 2 & 3 of

the transformer

secondary?

Replace

transformer.

Is there

voltage to the

COM of the door

switch?

Correct wiring

to door switch.

Check fuse.

Is there

voltage to the

N.O. terminal

of the door

switch?

Check door switch

and switch rod

for proper

operation. Replace

if necessary.

Is there

voltage to H2-8

of micro

control?

Correct wiring

between micro

control and door

switch.

Unit

operational.

Yes

Is there

voltage to H2-7 of

micro control?

Replace

micro control.

Is there

voltage across

the coil of the

M contactor?

Correct the wiring

to the

M contactor.

Is there

voltage to L1, L2

and L3 of the

M contactor?

Correct wiring

between M

contactor and

supply voltage.

Yes

Is there

voltage toT1, T2

and T3 of the

M contactor?

Replace

M contactor.

Is there

voltage across L1,

L2 and L3 of the

motor?

Correct wiring

between motor

and M contactor.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды