Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 68

Страница: 68 / 85

70410501

Troubleshooting

44. OM Reversing Models: No Cylinder Rotation or Reversing Capabilities

(continued)

208-240 Volt/60 Hertz/3 Phase and 480 Volt/60 Hertz/3 Phase CE Models
208-240 Volt/60 Hertz/3 Phase and 460-480 Volt/60 Hertz/3 Phase CG and CSH Models

Forward

Rotation: Is there

voltage across L1,

L2 and L3 of

the motor?

TMB2171S-b

Does the

motor turn?

Reverse

Rotation: Is

there voltage across

the coil of the

reverse relay?

Correct the

wiring to the

relay.

Reverse

Rotation: Is there

voltage to terminals X, Y

and Z of the reversing

relay?

Correct wiring

between relay

and supply

voltage.

Yes

Continued from

Reverse

Rotation: Is

there voltage to

H2-4 of micro

control?

Make sure unit

is in the reverse

portion of
rotation.

Replace micro

control.

Replace

motor.

Yes

Reverse

Rotation: Is there

voltage to terminals U, V

and W of the reversing

relay?

Replace

reversing

relay.

Yes

Reverse

Rotation: Is there

voltage across L1, L2

and L3 of the

motor?

Correct wiring

between motor

and reversing

relay.

Unit

operational.

Does the

cylinder rotate?

Check drive

components

between motor

and cylinder.

Yes

Correct wiring

between motor

and forward

relay.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды