Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 72

Страница: 72 / 85

70410501

Troubleshooting

47. MM Models: Cylinder Motor Does Not Run or Reverse With Door Closed,

Cycle Selected and Start Button Pressed In Reversing Mode or
Nonreversing Mode (continued)

208-240 Volt/60 Hertz/3 Phase Gas and Steam Reversing and 480 Volt/60 Hertz/3 Phase Steam
Reversing Models

NOTE: If unit will not reverse when reversing is selected, check for proper operation and wiring of reversing
switch. Replace if necessary.

there voltage to

L1, L2, L3 on the forward

contactor or voltage to

terminals X, Y and Z on

the reversing

contactor?

TMB2174S-b

Is there

voltage to the input

side of the auxiliary

contacts on the motor

contactor?

Is there

voltage across the

coils of either the

forward or reversing

contactor?

Replace either

the forward or

reversing

contactor.

Is there

voltage at the CW or

CCW terminal on the

solid state

timer?

Correct wiring

between the

solid state timer

and either the

forward or

reversing coil.

Yes

Continued from

Is there

voltage to L1, L2

and L3 at

motor?

Correct wiring

between

cylinder motor

and forward or

reversing

contactor.

Replace

motor

contactor.

Is there

voltage at L1 of the

solid state

timer?

Replace

solid state

timer.

Yes

Is there

voltage to the output

of the auxiliary contacts

on the motor

contactor?

Correct wiring

between

motor

contactor and

solid state

timer.

Unit

operational.

Yes

Correct wiring

between motor

contactor and

TB1-L1 supply.

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды