manualshive.com logo in svg

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Поделиться
Скачать
Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 13

70410501

11

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Troubleshooting

1. Motor Does Not Start

Motor does 

not start

Is the

electrical power

off or circuit breaker 

fuse blown?

No

Is the

loading door

not closed or switch 

inoperative?

Is the

door switch 

improperly 

adjusted?

No

Check power 

supply or replace 

fuses.

Yes

Close door or 

test switch and 

replace if 

inoperative.

Yes

Refer to 

Installation 

Manual 

 for 

door switch 

adjustment.

Yes

Is the start circuit 

not complete?

Yes

Press

 start switch 

or test switch 

and replace if 

inoperative.

Is the motor 

inoperative?

Yes

Have motor tested 

and replace if 

inoperative.

Refer to wiring 

diagram.

Yes

Are 

improper 

coins inserted in

accumulator?

Yes

Check that proper 

coins are inserted.

Is the

motor relay 

inoperative?

Yes

Test relay and 

replace if 

inoperative.

Is there

broken, loose, or 

incorrect

wiring?

No

TMB2131S-a

No

No

No

Is 

accumulator knob 

improperly set 

after coins were 

inserted.

Yes

Turn knob 

clockwise to its full 

limit of travel.

 Is the 

run switch 

accumulator 
inoperative?

Yes

Test run switch 

and replace if 

inoperative.

No

No

No

continued on 

next page

No

Содержание ATB50CG






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды