Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 81

Страница: 81 / 85

70410501

Troubleshooting

52. CD Models: No Start With Vend Satisfied and Start Button Pushed

240 Volt/60 Hertz/1 Phase Gas Nonreversing

NOTE: All voltage checks are referenced to neutral unless stated otherwise.

NOTE: If motor only runs with start switch pressed in, that means centrifugal switch in motor is bad.
Replace motor.

CD Models: No start with

vend satisfied and start

button pushed

Is there

voltage to

the N.C. terminal

of switch A?

TMB2179S-a

Correct wiring

between L1

on TBI and

switch A.

Is there

voltage to

COM terminal of

switch A?

Check for proper

operation of

switch A. Replace

switch A if

necessary.

Is there

voltage to COM

terminal of the

door switch?

Correct wiring

between door

switch and switch

A of the rotary

coin drop.

With the door

closed, is there voltage

to the N.O. terminal

of the door

switch?

Check door

switch for

proper

operation,

replace if

necessary.

Is there

voltage across

the coil of the

control relay

(CR)?

Correct wiring

to the control

relay.

Is there

voltage to terminal 5

of the motor?

Correct wiring

between

motor and

door switch.

Is there

voltage to the

input side of the

start switch?

Correct wiring

between start

switch and

door switch.

With the

start button pressed in,

is there voltage to the

output side of the start

button?

Replace start

switch.

Yes

Continued on

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды