Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 57

Страница: 57 / 85

70410501

Troubleshooting

38. CG OM Models: No Heat With Cycle Selected, Unit Running and Calling

For Heat

120 Volt/60 Hertz/1 Phase and 208-240 Volt/60 Hertz/1 Phase Nonreversing
208-240 Volt/60 Hertz/3 Phase and 460-480 Volt/60 Hertz/3 Phase Reversing and Nonreversing

CG OM Models: No heat with

cycle selected, unit running and

calling for heat

Is there

voltage

at H2-13?

Is there

voltage at H2-6

of the micro

control?

Correct wiring

between H2-5 and
H2-13 on the micro

control.

TMB2165S-a

Replace

micro control.

Is there

voltage at H2-5

of the micro

control?

Check for proper thermistor

operation. Replace micro

control if necessary.

Is there

voltage to input

of the motor

relay?

Correct wiring

between motor relay

and micro.

Is there

voltage to the

output of the

motor

relay?

Replace

motor relay.

1 Phase

Models: Is

there voltage

to terminal 3

of CR1?

Correct wiring between

CR1 and motor relay.

3 Phase

Models: Is

there voltage

to the input of

fan motor

switch?

Is there

voltage

to terminal 5

of CR1?

Correct wiring to fan

motor switch.

Is there

voltage out

from the

fan motor

switch?

Replace

fan motor.

Is there

voltage to

terminal 3 of

the motor?

Replace

motor.

Yes

Is there

voltage across

the coil

of CR1?

Correct wiring between

CR1 and motor.

Does CR1

operate

properly?

Replace

CR1.

Yes

Continued on

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды