Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 60

Страница: 60 / 85

70410501

Troubleshooting

40. MM Models: Fan Motor Does Not Run With Door Closed, Cycle Selected

and Start Button Pressed

208-240 Volt/60 Hertz/3 Phase Gas and Steam Reversing and Nonreversing; 480 Volt/60 Hertz/
3 Phase Gas Nonreversing; 480 Volt/60 Hertz/3 Phase Steam Reversing

NOTE: Make sure fuse on x1 of transformer is operational (240 Volt and 480 Volt/60 Hertz/3 Phase units).

MM Models: Fan motor

does not run with door

closed, cycle selected and

start button pressed

Is there

voltage to the COM

of the door

switch?

TMB2167S

Correct wiring

between door
switch and L1

supply for 208-240

Volt units. Check

between door

switch and X1 of

transformer for 480

Volt units.

Is there

120 VAC to the

N.O. terminal of the

door switch?

Check for proper

operation of

door switch arm

and/or replace

door switch.

Is there 120 VAC

to terminal P2 of the

micro control?

Correct wiring

between door

switch and

micro control.

Is there

120 VAC to

terminal P1 of the

micro control?

Replace

micro control.

Is there

120 VAC across

the coil of the motor

contactor?

Correct wiring to

the coil of motor

contactor.

Replace

motor.

Yes

Is there

voltage to terminals

L1, L2, and L3 of

motor contactor?

Correct wiring

between motor

contactor and

terminals L1, L2,

L3 and TB1.

Is there

voltage at

terminals T1, T2

and T3 of the M

contactor?

Replace motor

contactor.

Is there

voltage to L1,

L2 and L3 of

motor?

Correct wiring

between motor

and motor

contactor.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды