Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 61

Страница: 61 / 85

70410501

Troubleshooting

41. MM Models: Cylinder Motor Does Not Run or Reverse With Door Closed,

Cycle Selected and Start Button Pressed In Reversing Mode or
Nonreversing Mode

480 Volt/60 Hertz/3 Phase Steam Reversing and 208-240 Volt/60 Hertz/3 Phase Gas and Steam
Reversing Models

NOTE: If the unit will not reverse when reversing is selected, check for proper operation and wiring of
reversing switch. Replace if necessary.

MM Models: Cylinder

motor does not run or

reverse with door closed,

cycle selected and start

button pressed in

reversing mode or

nonreversing mode

Is there120 VAC

to the COM terminal

of the door switch?

TMB2168S-a

Correct wiring

between door
switch and L1

supply for 208-240

Volt units. Check

transformer on

480 volt.

Is there 120 VAC

to the N.O. terminal of

the door switch?

Check for proper

operation of door

switch arm and/or

replace door

switch.

Is there 120 VAC

to terminal P2 of the

micro control?

Correct wiring

between door

switch and micro

control.

Is there 120 VAC

to terminal P1 of the

micro control?

Replace

micro control.

Is there

120 VAC across the

coils of the motor

contactor?

Correct wiring to

the coil of motor

contactor.

Yes

Is there

voltage to terminals

L1, L2, and L3 of motor

contactor?

Correct wiring

between motor

contactor terminals

and L1, L2, L3

of TB1.

Is there

voltage at terminals

T1, T2 and T3 of the

M contactor?

Replace motor

contactor.

Is there

voltage to terminals

T1, T2, T3 on the forward

contactor and voltage to

terminals U, V and W on

the reversing

contactor?

Correct wiring

between forward

contactor and

motor contactor

and/or correct

wiring between

reverse contactor

and motor

contactor.

Yes

Continued on

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды