manualshive.com logo in svg

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Поделиться
Скачать
Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 27

70410501

25

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Troubleshooting

13. Heating Element or Burner Shuts-Off Prematurely

Heating element or 

burner shuts-off 

prematurely

Is there 

improper or 

inadequate 

exhaust and/or 

make-up air?

Refer to 

Installation 

Manual

 

for exhaust and 

make-up air 

requirements.

 Gas Models: Is 

there insufficient 

gas supply?

Open partially 

closed gas shut-off 

valve or correct low 

pressure.

Gas Models: 

Is tumbler 

not properly 

equipped for type 

of gas used?

Tumbler is 

equipped 

for type of gas 

specified on serial 

plate. If orifices are 

different from that 

specified on serial 

plate, obtain and 

install proper 

orifices.

Gas Models: 

Is burner flame 

improperly 

adjusted?

Refer to 

Installation 

Manual

 

for burner flame 

adjustment.

Is high limit 

thermostat 

cycling off?

Refer to 

Flowchart 14

.

Is there 

broken, loose 

or incorrect 

wiring?

Refer to 

wiring diagram 

located inside 

contactor box.

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Yes

TMB2142S

Glow-Bar Ignition 

Gas Models: Is sensor 

contact closing?

Replace 

sensor.

No

Yes

Содержание ATB50CG






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды