manualshive.com logo in svg

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Поделиться
Скачать
Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 37

70410501

35

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Troubleshooting

22. Troubleshooting Electronic Control Models (continued)

Display shows 

“SH” and signal 

sounds – Is 

temperature at 

sensor over 191˚F 

(88.3˚C)?

Allow tumbler to 

cool and press 

ON/SELECT 

pad. If display 

still shows “SH”, 

replace sensor.

TMB2149S-b

Yes

Replace 

temperature 

sensor.

Display shows 

“SH” and signal 

sounds – Is 

temperature 

sensor shorted?

Display shows 

“OP” and signal 

sounds three 
minutes after 

tumbler is started – 

Is temperature at 

sensor under 24˚F 

(-4.4˚C)?

If the 

temperature of 

the tumbler is 

above 24˚F 

(-4.4˚C), replace 

temperature 

sensor.

Display shows 

“OP” and signal 

sounds three 
minutes after 

tumbler is started 

– Is temperature 

sensor open?

Replace 

temperature 

sensor.

No

Yes

No

Yes

No

Yes

Continued from 

previous page 

Содержание ATB50CG






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды