Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 64

Страница: 64 / 85

70410501

Troubleshooting

42. MM Models: No Heat With Cycle Selected, Unit Running and Calling For

Heat (continued)

120 Volt/60 Hertz/1 Phase and 208-240 Volt/60 Hertz/1 Phase Gas and Steam Nonreversing
208-240 Volt/60 Hertz/3 Phase and 480 Volt/60 Hertz/3 Phase Steam Reversing and
Nonreversing

Is there voltage

to terminal 3

of CR2?

TMB2169S-b

Is there 120 VAC

on terminal 3

of motor?

Correct wiring

between CR2

and motor.

Is there voltage

across gas
valve coils?

Check wiring.

Replace IEI

board if

necessary.

Is the igniter

sparking?

Check

resistance of
high voltage

lead (5k and

20k). Replace

if necessary.

Yes

Continued from

Is there voltage

to L1 of IEI

board?

Correct wiring

between IEI

board and CR2.

Replace

motor.

Yes

Is there gas flow

through the valve?

Check for proper

gas pressure.

Replace gas valve

if necessary.

Yes

Is there voltage

across the coil

of CR2?

Replace

CR2.

Unit

operational.

Yes

Is there voltage

across the coil of the

steam valve?

Correct wiring

to steam

valve.

Yes

Does the

unit heat?

Check for proper

steam

supply. Replace

steam valve if

necessary.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды