Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 74

Страница: 74 / 85

70410501

Troubleshooting

48. MM Nonreversing Models: Motor Does Not Run With Door Closed, Cycle

Selected and Start Button Pressed (continued)

120 Volt/60 Hertz/1 Phase Gas and Steam; 208-240 Volt/60 Hertz/3 Phase Gas; 480 Volt/60
Hertz/3 Phase Steam

NOTE: Voltage checks referenced to are for neutral unless stated otherwise.

Is there

120 VAC on terminal

T1 of the motor relay for

single phase units, or across

T1, T2 and T3 for three

phase units?

TMB2175S-b

240 VAC units:

Is there 120 VAC to

terminal 1 of the

motor?

Correct wiring

between motor

CR1.

Is there

240 VAC across

terminals 1 and 4 of

the motor?

Yes

Continued from

Is there

120 VAC across the

terminals 1 and 4 of

the motor?

Correct wiring

to motor.

Replace

motor.

Yes

Replace motor

control relay.

Replace

motor.

Yes

Is there

120 VAC to terminal 8

of CR1?

Correct

wiring

between

CR1-8 and

L2.

Is there

120 VAC to terminal 7

of CR1?

Replace

CR1.

Correct wiring

between

CR1-7 and

terminal 4 of

the motor.

Yes

Is there

120 VAC on terminal

L1 of the motor relay for

single phase units, or across

L1, L2 and L3 for three

phase units?

Correct wiring

between motor

and motor

relay and the

terminal block.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды