Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 82

Страница: 82 / 85

70410501

Troubleshooting

52. CD Models: No Start With Vend Satisfied and Start Button Pushed

(continued)

240 Volt/60 Hertz/1 Phase Gas Nonreversing

NOTE: All voltage checks are referenced to neutral unless stated otherwise.

NOTE: If motor only runs with start switch pressed in, that means centrifugal switch in motor is bad.
Replace motor.

Is there

voltage to terminal 1

of the control

relay?

TMB2179S-b

Is there

voltage to terminal 1

of the motor?

Correct wiring

between

motor and

start switch.

Does the

motor run?

Replace the

motor.

Yes

Continued from

Is there voltage

to terminal 3 of

the control

relay?

Check for

proper

operation.

Replace

control relay if

necessary.

Yes

Unit

operational.

Correct wiring to

terminal 1 of the

control relay.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды