Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 80

Страница: 80 / 85

70410501

Troubleshooting

51. CD Models: No Heat With Vend Satisfied and Unit Running (continued)

120 Volt/60 Hertz/1 Phase and 240 Volt/60 Hertz/1 Phase Gas Nonreversing Models

there voltage

to the output side

of the adjustable

thermostat?

TMB2178S-b

Does the

igniter spark?

Check for proper gap on

igniter and check for proper

resistance of high voltage

lead. Replace lead if

necessary. (Proper gaps

for igniter are 5/16 above
burner and 5/32 between

electrode and grounding

tab. The proper resistance

of the high voltage lead

is between 5,000 Ohms

and 25,000 Ohms.)

Is there voltage

across V1 and V2

of the IEI board?

Replace

IEI board.

Yes

Continued from

Is there

voltage to L1 of the

ignition control board

(IEI board)?

Correct wiring

between

ignition control

board and

thermostat.

Yes

Replace

thermostat.

Yes

Is there voltage

across the coils of

the gas valve?

Is there

gas pressure on the

output side of the

gas valve?

Replace

gas valve.

Check for proper gas

pressure. 3.5 water

column inches for
Natural Gas, 10.5

water column inches

for L.P. Gas.

Yes

Is there

a flame?

Unit is

operational.

Yes

Correct wiring

between gas

valve and IEI

board.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды