Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 77

Страница: 77 / 85

70410501

Troubleshooting

50. CD Models: No Heat With Vend Satisfied and Unit Running

208-240 Volt/60 Hertz/3 Phase Gas Nonreversing

NOTE: All voltage checks are referenced to neutral unless stated otherwise.

CD Models: No heat

with vend satisfied

and unit running

Is there

voltage to the

input of the motor

switch?

TMB2177S-a

Correct wiring to

the input of motor

switch.

Is there

voltage to the

output of the motor

switch?

Replace

motor.

Is there voltage

to the input of the

cabinet limit?

Correct wiring

between cabinet

limit and motor

switch.

Is there voltage

to the output of the

cabinet limit?

Check for proper

operation, replace

if necessary.

there voltage

to the COM terminal

of the airflow

switch?

Correct wiring

between airflow

switch and

cabinet limit.

there voltage

to the N.O. terminal

of the airflow

switch?

Check for proper

airflow and

function of the

airflow switch.

Replace airflow

switch if

necessary.

there voltage

to the input of the

stove limit?

Correct wiring

between

stove limit and

airflow switch.

there voltage

to the output of the

stove limit?

Check for

blockage and

proper airflow.
Replace stove

limit if necessary.

Yes

Continued on

Yes

there voltage

to the N.C. terminal

of switch B?

Correct wiring

between switch B

and stove limit.

Yes

there voltage

to the COM terminal

of switch B?

Check for proper

operation, replace

switch B if

necessary.

Yes

Содержание ATB50CG






















































































Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Результаты поиска

Содержание ATB50CG

Отзывы:

Бренды по названию

Популярные бренды