manualshive.com logo in svg

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Поделиться
Скачать
Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 39

70410501

37

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Troubleshooting

24. Motor Runs, Time on Drying Timer But No Heat

Motor runs, time on 
drying timer but no 

heat

Is there 

power out of 

main control 

thermostat?

Check the 

ignition circuit.

TMB2151S-a

Yes

Is there 

power into 

main control 

thermostat?

Is 

there power 

on terminal 6 

of control 

relay?

Loose or broken 

wire to main 

control 

thermostat.

Is there 

power into 

airflow 

switch?

Is 

there power 

on terminal 4 

of control 

relay?

Replace 

control relay.

Is 

there power 

across coil 

terminals of 

control relay?

No

No

Yes

Yes

Yes

Is there a 

broken or 

loose wire at 

harness plug?

Repair 

wire.

Yes

Is there power 

on red wire 

from motor?

Replace 

motor.

No

No

Check for loose 

or broken wire 

from motor.

Is there 

power out 

of airflow 

switch?

Replace airflow 

switch.

Adjust airflow

switch.

No

No

Yes

No

Yes

Replace main 

control 

thermostat.

Yes

Is airflow 

switch 

closed?

No

Yes

No

Continued on 

next page 

Yes

Содержание ATB50CG






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды