manualshive.com logo in svg

Alliance Laundry Systems ATB50CG, Руководство по устранению неисправностей

Поделиться
Скачать
Alliance Laundry Systems ATB50CG Скачать руководство пользователя страница 24

22

70410501

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Troubleshooting

10. Igniter Glows, Sensor Opens But No Ignition – Johnson Controls System 

Gas Models

NOTE: To check the primary and secondary valve coil and plunger operation, place fingers on top of coils, 
cycle the machine and restart ignition circuit, you should feel the primary valve coil plunger open first, 
followed by glow bar heat up, followed by the sensor opening, and the secondary valve coil plunger opening. 
If plungers do not open, electrically check the coils. Check gas pressure to tumbler. Line pressure should be 
7 ± 1/2 inches (Natural Gas) or 11 inches (L.P. Gas) water column pressure. Manifold pressure should be 3.5 
inches (Natural Gas) or 11 inches (L.P. Gas) water column pressure.

Igniter glows, sensor 

opens but no ignition - 

Johnson Controls 

System Gas Models

Is gas supply
  insufficient?

Check gas supply 

and pressure.

Is there gas 

flow but no 

ignition?

Remove igniter and bracket and bend 

“L” shaped bracket (located on left 

side of stove) up or down. Reinstall 

igniter and bracket and check for 

1/8 to 1/4 inch gap between bottom 

of igniter and top of main burner.

Is there no 

gas flow 

through gas 

valve?

Check primary valve coil and plunger. 

Replace coil if inoperative, or check 

for 120 Volts to control relay (PR1) 

coil contacts (A) and 120 Volts to 

control relay (PR1) contact number 7. 

If no voltage, replace control relay 

(PR1) or check secondary valve coil 
and plunger operation. Replace coil 

if inoperative.

Yes

Yes

No

Yes

TMB2139S

No

Содержание ATB50CG






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды